More

  • Mill drives: the desire for increased power and the ...

    2021-12-17 · The standard method for sizing secondary ball mills (usually the overflow type) in AG/SAG circuits follows published mill supplier information with aspect ratios in the range 1:1.5 to 1:2.0, depending upon product sizing and pulp flow, i.e., the highest expected circulating loads (Morrell, 2001). The applied net power, calculated from testwork

    MORE
  • Resonance effects, power quality and reliability issues of ...

    2004-11-1 · Gearless drive for a SAG mill. Fig. 3 shows the comparison between a conventional pump drive and the gearless scheme using low-speed high-torque motor fed by a frequency converter. With a global efficiency of near 89% instead of 76%, the latter has an improvement in efficiency of about 13% because it has no gearbox losses.

    MORE
  • Testing Failure Criteria for Grinding Mill Structures

    2018-11-2 · The continuation of this trend, in spite of occasional mill failures, in both the SAG and ball mill areas, requires a requestioning of some basic design philosophies up to now utilized for large mills. The structural design criteria, simply stated, is based on two pieces of knowledge: The stresses existing in any area of the mill.

    MORE
  • TECHNICAL AND COMMERCIAL BENEFITS OF GEARLESS

    Errath, R., 2006, “The Gearless Mill Drive, the Work Horse for SAG and Ball Mills”, SME Conference, St. Louis. Protection and Supervision Systems for Gearless Mill Drives M Ahrens

    MORE
  • Copper Mountain Overview on the Grinding Mills and

    2015-7-29 · The grinding circuit consists of a SAG mill and two ball mills, all dual pinion gear driven. Copper . 3 Mountain has selected the state-of-the-art dual pinion mill drive systems, providing numerous advantageous features which were previously exclusively available on gearless mill drives.

    MORE
  • (PDF) Technical Evaluation and Practical Experience of ...

    Voltage waveform at the rectifier input side of an 18 000-hp LCI SAG mill drive. (a) Line-to-line bus voltage waveform (11 270-V peak). (b) Average rms value of the associated frequency spectrum ...

    MORE
  • BALL MILL GEARBOX PROBLEM - Vibration

    2019-10-30 · BALL MILL DRIVES, LOADED, WAVEFORM LEVELS, SEPTEMBER 1A 1B • Above is a plot of the waveform vibration levels at both the 1A & 1B ball mills when loaded (acceleration). • Note how waveform levels at 1A ball mill are higher than that at 1B ball mill for every measurement and especially at points PIH PIA (pillow block, coupling-end bearing).

    MORE
  • Gearless mill drives - Grinding | ABB

    Gearless mill drive system (GMD) Go gearless to meet your business objetives by exceeding standard availability targets in your grinding operations. ABB’s GMD is the most powerful mill drive system in the market to power semiautogenous

    MORE
  • Overflow VS Grate Discharge Ball or Mill - Why Retrofit

    2015-6-24 · Grate Discharge Ball Mills have shown 25% to 45% more tonnage ground and a substantial reduction in power consumed per ton of material compared size for size with overflow mills. To illustrate the characteristics of

    MORE
  • Resonance effects, power quality and reliability issues of ...

    2004-11-1 · Gearless drive for a SAG mill. Fig. 3 shows the comparison between a conventional pump drive and the gearless scheme using low-speed high-torque motor fed by a frequency converter. With a global efficiency of near 89% instead of 76%, the latter has an improvement in efficiency of about 13% because it has no gearbox losses.

    MORE
  • SAG mill ball charge determination and its influence on ...

    1990-5-24 · In semi-autogenous grinding (SAG), the grinding mill inventory, (i.e. volume of total charge, volume of ball charge, etc.) is important in determining the optimum operating condition for maximum production (tph), minimum specific energy (kwh/t) or lowest cost ($/t). A two-dimensional graphical method is presented for determining the actual ball charge within the

    MORE
  • Ball mill/SAG mill drive lubrication system | IEEE ...

    2015-4-30 · Ball mill/SAG mill drive lubrication system. Abstract: This paper describes the function and operation of lubrication systems for Ball Mill and SAG Mill Drives. Provided within this paper are hydraulic schematics, functional description and a general overview of system layout as well as some of the important features and factors relevant to ...

    MORE
  • Gearless Mill Drive Protection Improvements and Its ...

    2021-2-15 · Laguna Seca concentrator uses a SAG mill and three ball mills, all driven by gearless mill drive (GMD) systems. Table 1 gives an overview of the basic technical data of the installed drives. TABLE I. MILLS AND THEIR DRIVES IN THE LAGUNA SECA PLANT Equipment Drive Comments SAG Mill (Semi-autogenous Grinding) Quantity : 1 unit

    MORE
  • Engineering and Project Management History

    2021-12-9 · Ball Mill Gear Failure Analysis Analysis of SAG mill motor drive failures Regrind Mill Refurbishment Project management, inspection and technical services for refurbishment of used ball mill Oceanagold (Philippines), Inc. Didipio Gold Copper Project Project Coordination Ok Tedi Mining Limited, PNG Ball Mill Repairs Technical support

    MORE
  • Copper Mountain Overview on the Grinding Mills and

    2015-7-29 · The grinding circuit consists of a SAG mill and two ball mills, all dual pinion gear driven. Copper . 3 Mountain has selected the state-of-the-art dual pinion mill drive systems, providing numerous advantageous features which were previously exclusively available on gearless mill drives.

    MORE
  • TECHNICAL NOTES 8 GRINDING R. P. King

    2009-7-30 · LG A mill power equation for SAG mills. Minerals and Metallurgical Processing. Feb 1990 pp57-62. Gross power No load power Net power drawn by the charge (8.13) The net power is calculated from Net power KD2.5L e! c./ Watts (8.14) In equation 8.14, D is the diameter inside the mill liners and Le is the effective length of the mill including the ...

    MORE
  • TECHNICAL AND COMMERCIAL BENEFITS OF GEARLESS

    Errath, R., 2006, “The Gearless Mill Drive, the Work Horse for SAG and Ball Mills”, SME Conference, St. Louis. Protection and Supervision Systems for Gearless Mill Drives M Ahrens

    MORE
  • Lube Oil Trunnion Sag Mill - ulang

    2017729 Autogenous mills, semiautogenous mills and ball mills for wet grinding. A company of Polysius ThyssenKrupp caused by mill sag, thermal distortion and manufacturing tolerances. Hydrodynamic or oil leaks. The mill shell is a welded structure

    MORE
  • SAG MILL DISCHARGE SCREENS-TROMMEL vs.

    2013-12-22 · I’ve got to explain this a little bit. This flowsheet is typical of lines 1 and 3. The SAG mill has a trommel on the discharge end of it. Oversize is returned to the mill by a bucket wheel and water jet. Trommel undersize was pumped to a vibrating screen where the screen oversize was sent back to the mill and the undersize was pumped to the ...

    MORE
  • Resonance effects, power quality and reliability issues of ...

    2004-11-1 · For economy of scale, new projects consider grinding circuits with SAG and ball mills with 36′ or larger mill diameters with cycloconverter-fed drives with powers in the range near 20. MW.. For the huge volume of slurry flows, big pumps with low-speed gearless drives fed by medium voltage converters in the range of 1–2 MW are being considered.. Due to the high

    MORE
  • Gearless Mill Drive Protection Improvements and Its ...

    2021-2-15 · Laguna Seca concentrator uses a SAG mill and three ball mills, all driven by gearless mill drive (GMD) systems. Table 1 gives an overview of the basic technical data of the installed drives. TABLE I. MILLS AND THEIR DRIVES IN THE LAGUNA SECA PLANT Equipment Drive Comments SAG Mill (Semi-autogenous Grinding) Quantity : 1 unit

    MORE
  • SAG mill ball charge determination and its influence on ...

    1990-5-24 · In semi-autogenous grinding (SAG), the grinding mill inventory, (i.e. volume of total charge, volume of ball charge, etc.) is important in determining the optimum operating condition for maximum production (tph), minimum specific energy (kwh/t) or lowest cost ($/t). A two-dimensional graphical method is presented for determining the actual ball charge within the

    MORE
  • Ball mill/SAG mill drive lubrication system | IEEE ...

    2015-4-30 · Ball mill/SAG mill drive lubrication system. Abstract: This paper describes the function and operation of lubrication systems for Ball Mill and SAG Mill Drives. Provided within this paper are hydraulic schematics, functional description and a general overview of system layout as well as some of the important features and factors relevant to ...

    MORE
  • BALL MILL GEARBOX PROBLEM - Vibration

    2019-10-30 · BALL MILL DRIVES, LOADED, WAVEFORM LEVELS, SEPTEMBER 1A 1B • Above is a plot of the waveform vibration levels at both the 1A & 1B ball mills when loaded (acceleration). • Note how waveform levels at 1A ball mill are higher than that at 1B ball mill for every measurement and especially at points PIH PIA (pillow block, coupling-end bearing).

    MORE
  • Engineering and Project Management History

    2021-12-9 · Ball Mill Gear Failure Analysis Analysis of SAG mill motor drive failures Regrind Mill Refurbishment Project management, inspection and technical services for refurbishment of used ball mill Oceanagold (Philippines), Inc. Didipio Gold Copper Project Project Coordination Ok Tedi Mining Limited, PNG Ball Mill Repairs Technical support

    MORE
  • TECHNICAL AND COMMERCIAL BENEFITS OF GEARLESS

    Errath, R., 2006, “The Gearless Mill Drive, the Work Horse for SAG and Ball Mills”, SME Conference, St. Louis. Protection and Supervision Systems for Gearless Mill Drives M Ahrens

    MORE
  • TECHNICAL NOTES 8 GRINDING R. P. King

    2009-7-30 · LG A mill power equation for SAG mills. Minerals and Metallurgical Processing. Feb 1990 pp57-62. Gross power No load power Net power drawn by the charge (8.13) The net power is calculated from Net power KD2.5L e! c./ Watts (8.14) In equation 8.14, D is the diameter inside the mill liners and Le is the effective length of the mill including the ...

    MORE
  • Lube Oil Trunnion Sag Mill - ulang

    2017729 Autogenous mills, semiautogenous mills and ball mills for wet grinding. A company of Polysius ThyssenKrupp caused by mill sag, thermal distortion and manufacturing tolerances. Hydrodynamic or oil leaks. The mill shell is a welded structure

    MORE
  • Frozen charge detection and automatic loosening with ...

    2021-12-16 · Mill in Brazil and Lumwana having a 38ft, 18 MW SAG and one 26ft, 16 MW Ball Mill in Zambia, all three mills put in operation in 2008, as well as Los Bronces, Confluencia in Chile equipped with one 40ft SAG Mill of 22 MW and two 26ft Ball Mills of 16.4 MW commissioned in 2011. In the light of increasing interest in that technology various ...

    MORE

About Us

LTD which mainly manufacture large and medium-sized crushing and grinding equipments was founded in 1987. It is a modern joint-stock corporation with research, manufacturing and sales together.

Over the more than 30 years, our company adheres to modern scientific management system, precision manufacturing, pioneering and innovation. Now LIMING has become the leader in domestic and oversea machinery manufacturing industry.

read more

Contact us

Thank you for your interests in Liming Heavy Industry. Please feel free to submit your inquiry information to us. our sales manager will contact with you as soon as possible.

Email: [email protected]